Marquise Cut Diamonds: The Most Efficient Shape for Face-Up Size

The marquise has the largest face-up surface area per carat of any diamond shape. It is undervalued, deeply discounted vs round, and experiencing a quiet revival. Here is the full buying guide.

What makes the marquise unique

The marquise cut (also called navette — French for "little boat") is a modified brilliant with two sharp points at each end and an elliptical belly. Its elongated profile maximises the surface spread of a given carat weight more than any other shape. A 1.00 ct marquise at a length-to-width ratio of 2.00 presents more face-up surface area than a 1.00 ct oval, pear, or round of the same weight — the long, narrow profile distributes carat weight across the maximum possible surface.

This makes the marquise exceptional for buyers who prioritise visible size. A well-cut 0.90 ct marquise can look comparable in apparent size to a 1.10–1.20 ct round — a meaningful efficiency at higher price points where every 0.10 ct represents hundreds of dollars. GIA does not issue a cut grade for marquises; proportion evaluation is manual. Browse inventory at James Allen and Blue Nile.

Proportions and length-to-width ratio

Recommended marquise proportions based on PriceScope community consensus: Table 53–63%; Depth 58–68%; Length-to-width ratio 1.85–2.15 (the classic range); Polish and symmetry GIA Very Good or Excellent.

Wing symmetry is critical for marquises — the two pointed ends must be perfectly aligned, and the two wings must curve symmetrically. Asymmetric wings are a cutting defect visible to the naked eye when the stone is set. Check wing alignment in the 360° video by mentally drawing a vertical line through the centre — the two halves should be mirror images. Verify all proportion measurements at GIA Report Check.

Bow-tie and tip protection

Like ovals and pears, marquises typically display some degree of bow-tie shadow. Due to the extreme elongation, bow-ties in marquises can be more pronounced than in ovals. A slight bow-tie is acceptable and normal; a severe one is a permanent dark band. Only video evaluation under point-source light reveals severity — always use retailers who provide 360° video. Whiteflash and James Allen are the community-recommended sources for this.

Both pointed tips of a marquise are structurally vulnerable — as with pear cuts, V-prongs are essential at each end. Never set a marquise with exposed tips. The setting style has a dramatic effect on the marquise's appearance: a simple east-west solitaire setting maximises the elongation effect, while a vintage-style halo softens it considerably. Browse marquise settings at Brilliant Earth.

Marquise pricing in 2026

Marquise cuts trade at approximately 25–35% below equivalent round brilliants — one of the deepest discounts among the major fancy shapes. At 1.00 ct G/VS2, the absolute saving versus a round is typically $1,500–2,500. Combined with the face-up size advantage, this makes the marquise exceptionally strong value for budget-conscious buyers who like the shape.

The deep discount reflects the narrower buyer pool — the marquise peaked in popularity in the 1960s–80s and has been out of fashion for 30+ years, though it is showing signs of revival driven by celebrity influence and vintage-aesthetic trends. For buyers who genuinely like the shape, this out-of-fashion discount is a pure value opportunity. Benchmark at CaratAtlas using marquise shape factor. Full shape price map in our shape price discounts article.

Frequently asked questions

Is the marquise cut coming back in fashion?
Gradually. After 30+ years of declining popularity, marquise cuts are showing a modest revival driven by celebrity ring visibility and growing interest in vintage and non-traditional shapes. They remain deeply discounted vs rounds — 25–35% — meaning buyers who like the shape get exceptional value. Track trends at The Knot and Brides.
Why are marquise diamonds so cheap?
They trade at 25–35% below equivalent rounds because demand is low — fewer buyers want them, so sellers must price lower to find buyers. This is a pure market liquidity discount rather than a quality difference. The marquise has excellent optical performance when well-cut. If you like the shape, the discount is real savings. Live benchmarks at CaratAtlas.
What length-to-width ratio for a marquise?
1.85–2.15 is the classic range preferred by most buyers and the benchmark for the traditional marquise silhouette. Below 1.75 it looks too stubby; above 2.20 it becomes extremely elongated and may show a more severe bow-tie. Browse actual stones at James Allen to compare ratios in video.
Does a marquise need two V-prongs?
Yes — both pointed tips require V-prong (claw) protection. This is non-negotiable. An exposed marquise tip will chip eventually under normal wear. A four-prong or six-prong setting with V-tips at each end is the standard protective configuration. Browse settings at Brilliant Earth.

TERMS IN THIS NOTE

CutBow-tie effectCarat marquise vs ovalmarquise cut price 2026navette diamond